- Brownout detector was triggered
- ets Jun 8 2016 00:22:57
- rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
- configsip: 0, SPIWP:0xee
- clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
- mode:DIO, clock div:2
- load:0x3fff0018,len:4
- load:0x3fff001c,len:6352
- ho 0 tail 12 room 4
- load:0x40078000,len:11332
- load:0x40080400,len:6564
- entry 0x40080760
- [0;32mI (31) boot: ESP-IDF v3.3 2nd stage bootloader[0m
- [0;32mI (31) boot: compile time 06:11:15[0m
- [0;32mI (31) boot: Enabling RNG early entropy source...[0m
- [0;32mI (35) boot: SPI Speed : 40MHz[0m
- [0;32mI (39) boot: SPI Mode : DIO[0m
- [0;32mI (43) boot: SPI Flash Size : 4MB[0m
- [0;32mI (47) boot: Partition Table:[0m
- [0;32mI (51) boot: ## Label Usage Type ST Offset Length[0m
- [0;32mI (58) boot: 0 phy_init RF dat
- [17:11:23.808]收←◆ 3 at_customize unknown 40 00 00020000 000e0000[0m
- [0;32mI (88) boot: 4 ota_0 OTA app 00 10 00100000 00180000[0m
- [0;32mI (96) boot: 5 ota_1 OTA app 00 11 00280000 00180000[0m
- [0;32mI (103) boot: End of partition table[0m
- [0;32mI (107) esp_image: segment 0: paddr=0x00100020 vaddr=0x3f400020 size=0x247c4 (149444) map[0m
- [17:11:23.873]收←◆[0;32mI (169) esp_image: segment 1: paddr=0x001247ec vaddr=0x3ffbdb60 size=0x03028 ( 12328) load[0m
- [0;32mI (174) esp_image: segment 2: paddr=0x0012781c vaddr=0x40080000 size=0x00400 ( 1024) load[0m
- [0;32mI (176) esp_image: segment 3: paddr=0x00127c24 vaddr=0x40080400 size=0x083ec ( 33772) load[0m
- [0;32mI (199) esp_image: segment 4: paddr=0x00130018 vaddr=0x400d0018 size=0xee128 (975144) map[0m
- [17:11:24.498]收←◆[0;32mI (541) esp_image: segment 5: paddr=0x0021e148 vaddr=0x400887ec size=0x0f108 ( 61704) load[0m
- [0;32mI (567) esp_image: segment 6: paddr=0x0022d258 vaddr=0x400c0000 size=0x00064 ( 100) load[0m
- [0;32mI (581) boot: Loaded app from partition at offset 0x100000[0m
- [0;32mI (581) boot: Disabling RNG early entropy source...[0m
- Brownout detector was triggered
ESP32S烧录官方的AT固件,调试口一直重启,不知道什么原因
ESP32S烧录官方的AT固件,调试口一直重启,不知道什么原因
固件是2019.11能下载到最新的版本,DIO和QIO模式都试过,这是DIO模式下载后一直重启打印的信息,实在不知道那里出了问题
Who is online
Users browsing this forum: No registered users and 42 guests