I have custom board with ESP32-S3 and ESP32-C6 on it. I want to flash it with thread border router. I followed this tutorial: https://openthread.io/guides/border-rou ... ssif-esp32 and changed a few things.
I changed the target of OT-RCP from esp32h2 to esp32c6 and changed pins in `sdkconfig.ci.rcp` to:
CONFIG_OPENTHREAD_UART_PIN_MANUAL=y
CONFIG_OPENTHREAD_UART_RX_PIN=16
CONFIG_OPENTHREAD_UART_TX_PIN=17
and in esp-thread-br/examples/basic_thread_border_router I changed pins to:
CONFIG_PIN_TO_RCP_RESET=16
CONFIG_PIN_TO_RCP_BOOT=17
CONFIG_PIN_TO_RCP_TX=15
CONFIG_PIN_TO_RCP_RX=7
After flashing the firmware the esp is still restarting after a few seconds. The output is the following:
Code: Select all
SPIWP:0xee
Octal Flash Mode Enabled
For OPI Flash, Use Default Flash Boot Mode
mode:SLOW_RD, clock div:1
load:0x3fce3810,len:0x178c
load:0x403c9700,len:0x4
load:0x403c9704,len:0xbfc
load:0x403cc700,len:0x2d68
entry 0x403c9900
I (37) boot: ESP-IDF v5.3-dev-422-ga7fbf452fa-dirty 2nd stage bootloader
I (38) boot: compile time Nov 28 2023 20:54:03
I (39) boot: Multicore bootloader
I (43) boot: chip revision: v0.1
I (47) boot.esp32s3: Boot SPI Speed : 80MHz
I (51) boot.esp32s3: SPI Mode : SLOW READ
I (57) boot.esp32s3: SPI Flash Size : 4MB
I (61) boot: Enabling RNG early entropy source...
I (67) boot: Partition Table:
I (70) boot: ## Label Usage Type ST Offset Length
I (78) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (85) boot: 1 otadata OTA data 01 00 0000f000 00002000
I (93) boot: 2 phy_init RF data 01 01 00011000 00001000
I (100) boot: 3 ota_0 OTA app 00 10 00020000 00190000
I (108) boot: 4 ota_1 OTA app 00 11 001b0000 00190000
I (115) boot: 5 web_storage Unknown data 01 82 00340000 00019000
I (123) boot: 6 rcp_fw Unknown data 01 82 00359000 000a0000
I (130) boot: End of partition table
I (135) esp_image: segment 0: paddr=00020020 vaddr=3c0f0020 size=4ee3ch (323132) map
I (220) esp_image: segment 1: paddr=0006ee64 vaddr=3fc97b00 size=011b4h ( 4532) load
I (221) esp_image: segment 2: paddr=00070020 vaddr=42000020 size=ed8d8h (973016) map
I (457) esp_image: segment 3: paddr=0015d900 vaddr=3fc98cb4 size=039b0h ( 14768) load
I (461) esp_image: segment 4: paddr=001612b8 vaddr=40374000 size=13a50h ( 80464) load
I (493) boot: Loaded app from partition at offset 0x20000
I (493) boot: Disabling RNG early entropy source...
I (493) ��ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0xc (RTC_SW_CPU_RST),boot:0xb (SPI_FAST_FLASH_BOOT)
Saved PC:0x4037588d
0x4037588d: esp_restart_noos at /Users/filipmr/esp/esp-idf/components/esp_system/port/soc/esp32s3/system_internal.c:158What could cause the problem? I'm pretty much stuck and don't know how to investigate the error further. Is it possible to run a thread border router with C6 instead of H2?
Thank you for your answers.
PS: here is a simplified schematic of the board:
- schematic_tbr.png (510.28 KiB) Viewed 3134 times