ESP32 Forum

Code: Select all

//header
#define RX1 2
#define TX1 3

//setup()
Serial1.begin(115200, SERIAL_8N1, RX1, TX1);
Serial1.println("BOOT");

//function
class MyCallbacks: public BLECharacteristicCallbacks {
    void onWrite(BLECharacteristic *pCharacteristic) {
      std::string rxValue = pCharacteristic->getValue();

      if (rxValue.length() >= 6)
      {
        g_count_total_rx++;
        Serial.print("Received Value: ");

        char l_buffer[20] = {0};

        for (int i = 0; i < 6; i++)
        {
          Serial.print(rxValue[i], DEC);
          if(i<(rxValue.length()-1)) Serial.print("-");
        }

        Serial.println("");
        if(rxValue[0]==0xD0 && rxValue[5]==0xFF)
        {
            g_time_deep_sleep = 5000;                             //5 secondes
            g_timer_shutdown = 0;                                 //pour mettre à jour après la déco
            Serial.println("Entering deep speel mode");           //affichage sur la console
        }
        else
        {
          char l_buffer[20] = {0};
          for (int i = 0; i < 6; i++) Serial1.print(rxValue[i]);  //envoi à l'ECU
          sprintf(l_buffer, "Count %u\r\n", g_count_total_rx);
          bletx(l_buffer, strlen(l_buffer));                      //en onvoi le compre à l'appli
          Serial.print(l_buffer);                                 //affichage du comte sur la console
        }
      }
    }
};

Code: Select all

 for (int i = 0; i < 6; i++) Serial1.print(rxValue[i]);

Code: Select all

void setup() {
	Serial.begin(115200);
  Serial1.begin(115200,SERIAL_8N1,3,2);
  //Serial1.begin(115200,SERIAL_8N1,2,3);//tried both
}

void loop() {
	for(int i=0; i<17; i=i+8) {
	  chipId |= ((ESP.getEfuseMac() >> (40 - i)) & 0xff) << i;
	}

	Serial.printf("ESP32 Chip model = %s Rev %d\n", ESP.getChipModel(), ESP.getChipRevision());
	Serial.printf("This chip has %d cores\n", ESP.getChipCores());
  Serial.print("Chip ID: "); Serial.println(chipId);
  Serial1.printf("ESP32 Chip model = %s Rev %d\n", ESP.getChipModel(), ESP.getChipRevision());
  Serial1.printf("This chip has %d cores\n", ESP.getChipCores());
  Serial1.print("Chip ID: "); Serial.println(chipId);  
	delay(3000);

}

Code: Select all

/* UART Echo Example

   This example code is in the Public Domain (or CC0 licensed, at your option.)

   Unless required by applicable law or agreed to in writing, this
   software is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
   CONDITIONS OF ANY KIND, either express or implied.
*/
#include <stdio.h>
#include "freertos/FreeRTOS.h"
#include "freertos/task.h"
#include "driver/uart.h"
#include "driver/gpio.h"
#include "sdkconfig.h"

/**
 * This is an example which echos any data it receives on configured UART back to the sender,
 * with hardware flow control turned off. It does not use UART driver event queue.
 *
 * - Port: configured UART
 * - Receive (Rx) buffer: on
 * - Transmit (Tx) buffer: off
 * - Flow control: off
 * - Event queue: off
 * - Pin assignment: see defines below (See Kconfig)
 */

#define ECHO_TEST_TXD (CONFIG_EXAMPLE_UART_TXD)
#define ECHO_TEST_RXD (CONFIG_EXAMPLE_UART_RXD)
#define ECHO_TEST_RTS (UART_PIN_NO_CHANGE)
#define ECHO_TEST_CTS (UART_PIN_NO_CHANGE)

#define ECHO_UART_PORT_NUM      (CONFIG_EXAMPLE_UART_PORT_NUM)
#define ECHO_UART_BAUD_RATE     (CONFIG_EXAMPLE_UART_BAUD_RATE)
#define ECHO_TASK_STACK_SIZE    (CONFIG_EXAMPLE_TASK_STACK_SIZE)

#define BUF_SIZE (1024)

static void echo_task(void *arg)
{
    /* Configure parameters of an UART driver,
     * communication pins and install the driver */
    uart_config_t uart_config = {
        .baud_rate = ECHO_UART_BAUD_RATE,
        .data_bits = UART_DATA_8_BITS,
        .parity    = UART_PARITY_DISABLE,
        .stop_bits = UART_STOP_BITS_1,
        .flow_ctrl = UART_HW_FLOWCTRL_DISABLE,
        .source_clk = UART_SCLK_APB,
    };
    int intr_alloc_flags = 0;

#if CONFIG_UART_ISR_IN_IRAM
    intr_alloc_flags = ESP_INTR_FLAG_IRAM;
#endif

    ESP_ERROR_CHECK(uart_driver_install(ECHO_UART_PORT_NUM, BUF_SIZE * 2, 0, 0, NULL, intr_alloc_flags));
    ESP_ERROR_CHECK(uart_param_config(ECHO_UART_PORT_NUM, &uart_config));
    ESP_ERROR_CHECK(uart_set_pin(ECHO_UART_PORT_NUM, ECHO_TEST_TXD, ECHO_TEST_RXD, ECHO_TEST_RTS, ECHO_TEST_CTS));

    // Configure a temporary buffer for the incoming data
    uint8_t *data = (uint8_t *) malloc(BUF_SIZE);

    while (1) {
        // Read data from the UART
        int len = uart_read_bytes(ECHO_UART_PORT_NUM, data, BUF_SIZE, 20 / portTICK_RATE_MS);
        // Write data back to the UART
        uart_write_bytes(ECHO_UART_PORT_NUM, (const char *) data, len);
    }
}

void app_main(void)
{
    xTaskCreate(echo_task, "uart_echo_task", ECHO_TASK_STACK_SIZE, NULL, 10, NULL);
}

Code: Select all

  char ltmp[20];
  sprintf(ltmp,"UART1 ready\r\n");

  uart_t* p_uart = uartBegin(0, 115200, SERIAL_8N1 , 2, 3, 100, 0, 122);
  uartWriteBuf(p_uart, (uint8_t*)ltmp, 12);

  Serial.println("Waiting a client connection to notify...");

Code: Select all

// ESP32 C3 SERIAL1  (second Uart)
void setup() {
   Serial.begin(115200);
   Serial1.begin(115200,SERIAL_8N1, 4,5); //int8_t rxPin=4, int8_t txPin=5 
}

void loop() {
    if (Serial.available()) {      // If anything comes in Serial (USB),
    Serial1.write(Serial.read());   // read it and send it out Serial1 (pins 4 & 5)
  }

  if (Serial1.available()) {     // If anything comes in Serial1 (pins 4 & 5)
    Serial.write(Serial1.read());   // read it and send it out Serial (USB)
  }
}