ESP-CAM image shows artifacts.

[audrudals]

Hello forum,
I am trying to host a web server that returns the captured camera image, but the downloaded image shows weird artifacts.
The top half is normal, but the bottom half look like it is being overwritten or half written, with offset images and weird color banding.
I checked if PSRAM is insufficient, but there were plenty left.
Any help will be appreciated:)
The code is as following:

Code: Select all

#include <WiFi.h>
#include <ESPAsyncWebServer.h>
#include <esp_camera.h>
#define CAMERA_MODEL_AI_THINKER
#include "camera_pins.h"

const char *ssid = "";
const char *password = "";

AsyncWebServer server(80);

void initCamera() {
  camera_config_t config;
  config.ledc_channel = LEDC_CHANNEL_0;
  config.ledc_timer = LEDC_TIMER_0;
  config.pin_d0 = Y2_GPIO_NUM;
  config.pin_d1 = Y3_GPIO_NUM;
  config.pin_d2 = Y4_GPIO_NUM;
  config.pin_d3 = Y5_GPIO_NUM;
  config.pin_d4 = Y6_GPIO_NUM;
  config.pin_d5 = Y7_GPIO_NUM;
  config.pin_d6 = Y8_GPIO_NUM;
  config.pin_d7 = Y9_GPIO_NUM;
  config.pin_xclk = XCLK_GPIO_NUM;
  config.pin_pclk = PCLK_GPIO_NUM;
  config.pin_vsync = VSYNC_GPIO_NUM;
  config.pin_href = HREF_GPIO_NUM;
  config.pin_sccb_sda = SIOD_GPIO_NUM;
  config.pin_sccb_scl = SIOC_GPIO_NUM;
  config.pin_pwdn = PWDN_GPIO_NUM;
  config.pin_reset = RESET_GPIO_NUM;
  config.xclk_freq_hz = 20000000;
  config.frame_size = FRAMESIZE_UXGA;
  config.pixel_format = PIXFORMAT_JPEG;  // for streaming
  //config.pixel_format = PIXFORMAT_RGB565; // for face detection/recognition
  config.grab_mode = CAMERA_GRAB_WHEN_EMPTY;
  config.fb_location = CAMERA_FB_IN_PSRAM;
  config.jpeg_quality = 12;
  config.fb_count = 1;

  // if PSRAM IC present, init with UXGA resolution and higher JPEG quality
  //                      for larger pre-allocated frame buffer.
  if (config.pixel_format == PIXFORMAT_JPEG) {
    if (psramFound()) {
      config.jpeg_quality = 10;
      config.fb_count = 2;
      config.grab_mode = CAMERA_GRAB_LATEST;
    } else {
      // Limit the frame size when PSRAM is not available
      config.frame_size = FRAMESIZE_SVGA;
      config.fb_location = CAMERA_FB_IN_DRAM;
    }
  } else {
    // Best option for face detection/recognition
    config.frame_size = FRAMESIZE_240X240;
#if CONFIG_IDF_TARGET_ESP32S3
    config.fb_count = 2;
#endif
  }

  esp_err_t err = esp_camera_init(&config);
  if (err != ESP_OK) {
    Serial.printf("Camera init failed with error 0x%x", err);
    ESP.restart();
  }
}

void setup() {
  Serial.begin(115200);

  WiFi.begin(ssid, password);
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("\nWiFi connected");
  Serial.println("IP address: ");
  Serial.println(WiFi.localIP());

  initCamera();

  server.on("/capture", HTTP_GET, [](AsyncWebServerRequest* request) {
    Serial.printf("Free PSRAM: %d bytes\n", ESP.getFreePsram());

    camera_fb_t* fb = esp_camera_fb_get(); // Capture a frame
    if (!fb) {
      Serial.println("Camera capture failed");
      request->send(500, "text/plain", "Camera capture failed");
      return;
    }

    AsyncWebServerResponse* response = request->beginResponse_P(200, "image/jpeg", fb->buf, fb->len);
    response->addHeader("Content-Disposition", "inline; filename=capture.jpg");
    request->send(response);

    esp_camera_fb_return(fb);
  });

  server.begin();
}

void loop() {}

capture.jpg (98.92 KiB) Viewed 568 times

[aliarifat794]

You can reduce Frame Size. High resolutions like FRAMESIZE_UXGA (1600x1200) consume significant memory. Lower the frame size to reduce strain:

Code: Select all

config.frame_size = FRAMESIZE_SXGA; // or FRAMESIZE_XGA

You can reduce the buffer count if two frame buffers are too demanding:

Code: Select all

config.fb_count = 1;

You can edit your initialization like this:

Code: Select all

void initCamera() {
  camera_config_t config;
  config.ledc_channel = LEDC_CHANNEL_0;
  config.ledc_timer = LEDC_TIMER_0;
  config.pin_d0 = Y2_GPIO_NUM;
  config.pin_d1 = Y3_GPIO_NUM;
  config.pin_d2 = Y4_GPIO_NUM;
  config.pin_d3 = Y5_GPIO_NUM;
  config.pin_d4 = Y6_GPIO_NUM;
  config.pin_d5 = Y7_GPIO_NUM;
  config.pin_d6 = Y8_GPIO_NUM;
  config.pin_d7 = Y9_GPIO_NUM;
  config.pin_xclk = XCLK_GPIO_NUM;
  config.pin_pclk = PCLK_GPIO_NUM;
  config.pin_vsync = VSYNC_GPIO_NUM;
  config.pin_href = HREF_GPIO_NUM;
  config.pin_sccb_sda = SIOD_GPIO_NUM;
  config.pin_sccb_scl = SIOC_GPIO_NUM;
  config.pin_pwdn = PWDN_GPIO_NUM;
  config.pin_reset = RESET_GPIO_NUM;
  config.xclk_freq_hz = 20000000;
  config.frame_size = FRAMESIZE_XGA; // Lowered frame size for stability
  config.pixel_format = PIXFORMAT_JPEG;
  config.fb_location = CAMERA_FB_IN_PSRAM; // Change to DRAM for testing
  config.jpeg_quality = 12;
  config.fb_count = 1;

  if (psramFound()) {
    config.jpeg_quality = 10;
    config.fb_count = 2;
    config.grab_mode = CAMERA_GRAB_WHEN_EMPTY; // Default for PSRAM
  }

  esp_err_t err = esp_camera_init(&config);
  if (err != ESP_OK) {
    Serial.printf("Camera init failed with error 0x%x", err);
    ESP.restart();
  }
}

You can also see this project: https://www.pcbway.com/project/sharepro ... d7727.html