Bios Default BAUD [esp8266]

KevinA
Posts: 14
Joined: Tue Sep 20, 2016 3:09 pm

Bios Default BAUD [esp8266]

Postby KevinA » Sun Oct 02, 2016 9:26 pm

While working on the latest SDK I was trying to figure out the garbage on my screen every time I rebooted to discover 74880 baud would allow me to see what was being dumped to the screen. Is there a reason for 74880 instead of a standard baud rates? Some terminal programs do not have 74880 support and there are plenty of posts about garbage at the esp8266 forum.

User avatar
kolban
Posts: 1683
Joined: Mon Nov 16, 2015 4:43 pm
Location: Texas, USA

Re: Bios Default BAUD

Postby kolban » Sun Oct 02, 2016 10:20 pm

I am finding that my default baud rate after a reboot is 115200. I am using the latest ESP-IDF images from Github and am using a DevKitC board made by Espressif to host my ESP32. Now ... I am also flashing the device at 115200. When I tried to flash it with a faster rate ... i.e 230400 that worked ... however on reboot, I found that at the initial start of a soft reboot, the speed remained at 230400 until somewhere into the boot process where it seemed to switch back to 115200. So far, I haven't seen a 74880 on my ESP32 travels.
Free book on ESP32 available here: https://leanpub.com/kolban-ESP32

a2retro
Posts: 56
Joined: Tue Dec 01, 2015 3:09 am

Re: Bios Default BAUD

Postby a2retro » Mon Oct 03, 2016 3:01 pm

I find 921,600 with compressed works quite nicely for me using my Particle Programmer board. I have not tried that speed via the built in silabs interface yet.

Edit: 921,600 also works for me on the silabs interface

KevinA
Posts: 14
Joined: Tue Sep 20, 2016 3:09 pm

Re: Bios Default BAUD

Postby KevinA » Tue Oct 18, 2016 5:59 am

My bad, I should have posted in the esp8266 forum, the latest NodeMCU from LoLin has sdk 5.2 on it and this is what it does:

print(uart.setup(0, 74880, 8, 0, 1, 1 ))

ERROR

Communication with MCU..Got answer! Communication with MCU established.
AutoDetect firmware...

Can't autodetect firmware, because proper answer not received (may be unknown firmware).
Please, reset module or continue.
boot mode:(3,6)

load 0x40100000, len 1856, room 16
tail 0
chksum 0x63
load 0x3ffe8000, len 776, room 8
tail 0
chksum 0x02
load 0x3ffe8310, len 552, room 8
tail 0
chksum 0x79
csum 0x79

2nd boot version : 1.5
SPI Speed : 40MHz
SPI Mode : DIO
SPI Flash Size & Map: 8Mbit(512KB+512KB)
jump to run user1 @ 1000

È[ƒÐÚ�R+­¨R�
After I can switch to 115200 and read everything.
AT+GMR

AT version:0.60.0.0(Jan 29 2016 15:10:17)
SDK version:1.5.2(7eee54f4)
Ai-Thinker Technology Co. Ltd.
May 5 2016 17:30:30
OK

But I haven't gotten my ESP3212 boards yet, still waiting..

ESP_Angus
Posts: 2344
Joined: Sun May 08, 2016 4:11 am

Re: Bios Default BAUD [esp8266]

Postby ESP_Angus » Tue Oct 18, 2016 10:42 pm

Thanks for updating Kevin. The 74880 on esp8266 is an artifact of the crystal speed (if you use a 40MHz crystal the baud rate is 115200, but everyone uses 26MHz crystals so it's proportionally lower.) On ESP32 the default baud rate is 115200 regardless of crystal clock rate.

Who is online

Users browsing this forum: No registered users and 5 guests