ESP32 Forum

Code: Select all

   
    ethernet_events = xEventGroupCreate();
    esp_netif_init();
    esp_event_loop_create_default();
    // Register user defined event handers
    ESP_ERROR_CHECK(esp_event_handler_register(ETH_EVENT, ESP_EVENT_ANY_ID, event_handler_for_ethernet, NULL));
    ESP_ERROR_CHECK(esp_event_handler_register(IP_EVENT, IP_EVENT_ETH_GOT_IP, event_handler_for_ethernet, NULL));

    esp_netif_config_t netif_cfg = ESP_NETIF_DEFAULT_ETH();
    eth_netif = esp_netif_new(&netif_cfg);

    spi_bus_config_t buscfg = {
        .miso_io_num = ETH_SPI_MISO,
        .mosi_io_num = ETH_SPI_MOSI,
        .sclk_io_num = ETH_SPI_SCK,
        .quadwp_io_num = -1,
        .quadhd_io_num = -1,
    };
    ESP_ERROR_CHECK(spi_bus_initialize(ETH_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO));
    /* ENC28J60 ethernet driver is based on spi driver */
    spi_device_interface_config_t devcfg = {
        .command_bits = 3,
        .address_bits = 5,
        .mode = 0,
        .clock_speed_hz = ETH_SPI_CLOCK_MHZ * 1000 * 1000,
        .spics_io_num = ETH_CS_GPIO,
        .queue_size = 20,
        .cs_ena_posttrans = enc28j60_cal_spi_cs_hold_time(ETH_SPI_CLOCK_MHZ),
    };

    spi_device_handle_t spi_handle = NULL;
    ESP_ERROR_CHECK(spi_bus_add_device(ETH_SPI_HOST, &devcfg, &spi_handle));

    eth_enc28j60_config_t enc28j60_config = ETH_ENC28J60_DEFAULT_CONFIG(spi_handle);
    enc28j60_config.int_gpio_num = ETH_INT_GPIO;

    eth_mac_config_t mac_config = ETH_MAC_DEFAULT_CONFIG();
    mac_config.smi_mdc_gpio_num = -1; // ENC28J60 doesn't have SMI interface
    mac_config.smi_mdio_gpio_num = -1;
    esp_eth_mac_t *mac = esp_eth_mac_new_enc28j60(&enc28j60_config, &mac_config);

    eth_phy_config_t phy_config = ETH_PHY_DEFAULT_CONFIG();
    phy_config.autonego_timeout_ms = 0; // ENC28J60 doesn't support auto-negotiation
    phy_config.reset_gpio_num = -1;     // ENC28J60 doesn't have a pin to reset internal PHY
    esp_eth_phy_t *phy = esp_eth_phy_new_enc28j60(&phy_config);

    esp_eth_config_t eth_config = ETH_DEFAULT_CONFIG(mac, phy);
    esp_eth_handle_t eth_handle = NULL;
    ESP_ERROR_CHECK(esp_eth_driver_install(&eth_config, &eth_handle));

    /* ENC28J60 doesn't burn any factory MAC address, we need to set it manually.
       02:00:00 is a Locally Administered OUI range so should not be used except when testing on a LAN under your control.
    */

    mac->set_addr(mac, (uint8_t[]){
                           mac_addr[0], mac_addr[1], mac_addr[2], mac_addr[3], mac_addr[4], mac_addr[5]});

    // ENC28J60 Errata #1 checkETH_SPI_CLOCK_MHZ
    if (emac_enc28j60_get_chip_info(mac) < ENC28J60_REV_B5 && ETH_SPI_CLOCK_MHZ < 8)
    {
        ESP_LOGE(TAG, "SPI frequency must be at least 8 MHz for chip revision less than 5");
        ESP_ERROR_CHECK(ESP_FAIL);
    }
    // Stop DHCP --------------------------------------------------------------------------------------------------

    /* attach Ethernet driver to TCP/IP stack */
    ESP_ERROR_CHECK(esp_netif_attach(eth_netif, esp_eth_new_netif_glue(eth_handle)));

    /* It is recommended to use ENC28J60 in Full Duplex mode since multiple errata exist to the Half Duplex mode */
    // if CONFIG_EXAMPLE_ENC28J60_DUPLEX_FULL
    /* Set duplex needs to be called after esp_eth_start since the driver is started with auto-negotiation by default */
    err = enc28j60_set_phy_duplex(phy, ETH_DUPLEX_FULL);

    if (err == ESP_OK)
    {
        ESP_LOGI(TAG, "[ ETHERNET TRANSMISSION MODE SET TO FULL DUPLEX ]");
    }

    // #endif
    /* start Ethernet driver state machine */
    err = esp_eth_start(eth_handle);

    if (err == ESP_OK)
        ESP_LOGI(TAG, "ETHERNET Started successfully");
    else
        ESP_LOGE(TAG, "ETHERNET Start failed");

    xEventGroupWaitBits(ethernet_events, CONNECTED_GOT_IP | DISCONNECTED, pdTRUE, pdFALSE, pdMS_TO_TICKS(10000));

    esp_netif_dhcp_status_t status;
    esp_netif_dhcpc_get_status(eth_netif, &status);
    ESP_LOGW(TAG, " DHCPC  (state=%u)", status);
    if (status == 0x0)
    {
        esp_err_t err_dhcp = esp_netif_dhcpc_start(eth_netif);
        ESP_LOGI(TAG, "DHCP client status : %s", esp_err_to_name(err_dhcp));
    }
  

Code: Select all

esp_netif_dhcpc_start(eth_netif, pdMS_TO_TICKS(10000)); // Increase timeout to 10 seconds

Code: Select all

esp_netif_dhcpc_start()