OMG I'm crying
Search found 300 matches
- Thu Apr 29, 2021 9:47 am
- Forum: ESP32 Arduino
- Topic: ESP32 is the worst microcontroller I played with
- Replies: 14
- Views: 30255
- Thu Apr 29, 2021 9:13 am
- Forum: ESP32 Arduino
- Topic: ESP32 is the worst microcontroller I played with
- Replies: 14
- Views: 30255
Re: ESP32 is the worst microcontroller I played with
Hi, I think you should post a few issues and seek help if you have problems. I'm sure there are solutions for most of the problems you are having. I also think Espressif will welcome feedback from people who push their devices to the limit, so they can learn and imporve the software that goes along ...
- Wed Apr 28, 2021 5:22 am
- Forum: General Discussion
- Topic: I couldnt upload code. it stucks at %6 and give timeout error.
- Replies: 3
- Views: 4908
Re: I couldnt upload code. it stucks at %6 and give timeout error.
I'm glad it worked out for youdemirdemirel wrote: ↑Tue Apr 27, 2021 5:53 pmHi,
Thank you for your reply. It was very helpful to detect and solve the problem.
Long story short, I use an external power supply and the magic happened.
I will buy another bunch of USB cables.
- Tue Apr 27, 2021 12:49 pm
- Forum: Hardware
- Topic: 32kHz oscillator on ESP-WROVER-KIT-VE not working
- Replies: 13
- Views: 14566
Re: 32kHz oscillator on ESP-WROVER-KIT-VE not working
Hello, yes, the 0ohm resistors between crystal and module pins are present yes. I've set external crystal in the menuconfig You should also make a continuity check from the pins on the wrover module to the pads of the crystal. This will check if everything is soldered correctly and the 0ohm chip re...
- Tue Apr 27, 2021 11:19 am
- Forum: General Discussion
- Topic: ESP32-S3 (Beta2) MARLIN_9_1B on ESP32-S3-Addax-1 V1.0 Specs & Datasheet
- Replies: 74
- Views: 181412
Re: ESP32-S3 (Beta2) MARLIN_9_1B on ESP32-S3-Addax-1 V1.0 Specs & Datasheet
I agree. Excitement intesifies!rudi ;-) wrote: ↑Tue Apr 27, 2021 10:50 amVader_Mester wrote: ↑Mon Apr 26, 2021 10:13 amWell, I'm glad me and my company signed an NDA with Espressif
- Tue Apr 27, 2021 6:40 am
- Forum: Hardware
- Topic: ESP32 Wrover Cannot Flash Firmware Need Help
- Replies: 1
- Views: 2989
Re: ESP32 Wrover Cannot Flash Firmware Need Help
I don't see any issue with the schematic at first glance, only that D0 should have a Pull-Up? If you look at https://dl.espressif.com/dl/schematics/ESP-WROVER-KIT_SCH-2.pdf , bottom right corner of the PDF, you can see that every signal on the SD-Card connector have pull-ups, even data lines as well...
- Mon Apr 26, 2021 1:33 pm
- Forum: ESP32 Arduino
- Topic: BluetoothSerial's .println() is altering hardware timer interrupt on other core
- Replies: 5
- Views: 4801
Re: BluetoothSerial's .println() is altering hardware timer interrupt on other core
The BT task and interrupts run at core 0 by default, if memory serves. This happens even if you print to BT on the other core. Presumably the BT interrupts pre-empt your timer interrupt. But, I checked within the interrupt which core it runs on via xPortGetCoreID(), and it runs on the core in which...
- Mon Apr 26, 2021 10:13 am
- Forum: General Discussion
- Topic: ESP32-S3 (Beta2) MARLIN_9_1B on ESP32-S3-Addax-1 V1.0 Specs & Datasheet
- Replies: 74
- Views: 181412
Re: ESP32-S3 (Beta2) MARLIN_9_1B on ESP32-S3-Addax-1 V1.0 Specs & Datasheet
Do you know if uFL connector versions will come from these modules as well? the mini serie contains mini-1 (PCB Ant) and mini-1U (IPEX), also final S3 series there will been MINI module and from hearing - WROOM module - not hearing - WROVER module - I just did a pin-map of the WROVER-like module on...
- Mon Apr 26, 2021 10:09 am
- Forum: General Discussion
- Topic: I couldnt upload code. it stucks at %6 and give timeout error.
- Replies: 3
- Views: 4908
Re: I couldnt upload code. it stucks at %6 and give timeout error.
Hi, It doesn't fail at the same stage, so my guess is that either there is interference on the UART signal lines, or you have power supply issues and either your converter or the ESP module itself resets. This can happen when the supply voltage is not high enough, or you have poor supply filtering o...
- Fri Apr 23, 2021 11:04 am
- Forum: Hardware
- Topic: ReWrite BLK3 ADC TP calibration values esp32 eFuse?
- Replies: 2
- Views: 3197
Re: ReWrite BLK3 ADC TP calibration values esp32 eFuse?
Hi, eFuse can not be rewritten. It is only possible to write it once (hence the name). You could change bit in the eFuse that are 0, to 1, but not the other way. For details, I suggest you read this: https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-reference/peripherals/adc.html#adc-c...