Same error with 5.1.4.
I installed git from the mint software manager, and then idf.py complained about cmake not being on the path. So I installed cmake as well and now compilation works.
Cmake is listed in the esp-idf docs as a prerequisite, but git is not.
Thanks very much for your help.
Search found 13 matches
- Mon May 20, 2024 8:11 pm
- Forum: ESP-IDF
- Topic: compile of app fails with FileNotFoundError: [Errno 2] No such file or directory: 'git' (IDF-10003)
- Replies: 3
- Views: 1174
- Mon May 20, 2024 1:47 am
- Forum: ESP-IDF
- Topic: compile of app fails with FileNotFoundError: [Errno 2] No such file or directory: 'git' (IDF-10003)
- Replies: 3
- Views: 1174
compile of app fails with FileNotFoundError: [Errno 2] No such file or directory: 'git' (IDF-10003)
This is with a new install of v5.1.1 on a new install of linux mint 21.3. The install of v5.1.1 went fine the second time after I manually installed python3.10-venv. v5.1.1 works fine on another system I have running mint 20.3. WARNING: Git was not found WARNING: Git was not found WARNING: Git was n...
- Mon Apr 17, 2023 2:21 am
- Forum: General Discussion
- Topic: esp32-s3 serial port over usb
- Replies: 9
- Views: 4928
Re: esp32-s3 serial port over usb
Good point on the caps -- I'll add them. Thanks for taking a look.
- Mon Apr 17, 2023 1:52 am
- Forum: General Discussion
- Topic: esp32-s3 serial port over usb
- Replies: 9
- Views: 4928
Re: esp32-s3 serial port over usb
Cool, thanks.
- Sun Apr 16, 2023 10:40 pm
- Forum: General Discussion
- Topic: esp32-s3 serial port over usb
- Replies: 9
- Views: 4928
Re: esp32-s3 serial port over usb
My own board design. It's pretty simple - just an ap2115 regulator, a usb4105-gf-a receptacle, a couple of headers, and some buttons for EN and IO0.
- Fri Apr 14, 2023 2:17 am
- Forum: General Discussion
- Topic: esp32-s3 serial port over usb
- Replies: 9
- Views: 4928
Re: esp32-s3 serial port over usb
No luck with this. I reflashed with the menuconfig console output set to USB Serial/JTAG Controller, then plugged in the usb cable, rebooted with GPIO0 grounded. I have verified the sketch is running, but no new ports show up. I've probed inside the female A end of the cable to verify the connection...
- Wed Apr 12, 2023 1:13 am
- Forum: General Discussion
- Topic: esp32-s3 serial port over usb
- Replies: 9
- Views: 4928
esp32-s3 serial port over usb
One of the answers to another question https://esp32.com/viewtopic.php?f=2&t=28326 says: The -S3 has both an USB-serial-JTAG device as well as a 'general-purpose' USB-OTG peripheral. The device you see on bootup is the USB-serial-JTAG unit; it does not need software to work and as such you can progr...
- Tue Apr 11, 2023 2:33 am
- Forum: General Discussion
- Topic: new esp32-s3 misbehaving
- Replies: 2
- Views: 1333
Re: new esp32-s3 misbehaving
Yes, that was it.
Many thanks!
Many thanks!
- Mon Apr 10, 2023 3:43 pm
- Forum: General Discussion
- Topic: new esp32-s3 misbehaving
- Replies: 2
- Views: 1333
new esp32-s3 misbehaving
I have a new s3 breakout board which I made. I can program it successfully using an ftdi usb adapter, but after reboot I get a couple of boot messages and then just lot of invalid header errors: "invalid header: 0xa5ff005a". Anyone have any ideas or debugging suggestions? The output is as follows: ....
- Tue Jun 07, 2022 1:59 am
- Forum: Hardware
- Topic: IO7 and IO8 on PICO devkit M-2
- Replies: 1
- Views: 1188
IO7 and IO8 on PICO devkit M-2
Got a ESP32-PICO-DevKitM-2 board and found the pinouts are different from the ESP32-PICO-KIT V4.1 I was using before. IO23 and IO18 are gone, but IO7 and IO8 are new. The datasheet has: IO7: GPIO7, HS1_DATA0, U2RTS, SD_DATA0 IO8: GPIO8, HS1_DATA1, U2CTS, SD_DATA1 In the PICO-D4 GPIO7 and GPIO8 were ...