Search found 202 matches
- Thu Apr 06, 2023 1:38 pm
- Forum: Hardware
- Topic: Why TxTimestampStatus is alway 0, for esp32's IEEE 1588
- Replies: 5
- Views: 3962
Re: Why TxTimestampStatus is alway 0, for esp32's IEEE 1588
I investigated and discussed internally and I have bad news... Hardware time-stamping cannot be used on ESP32 (neither PTPv1 nor PTPv2).
- Wed Apr 05, 2023 1:53 pm
- Forum: ESP-IDF
- Topic: EMAC TX buffer runs full when no connection is established "emac_esp32_transmit(): insufficient TX buffer size"
- Replies: 1
- Views: 2180
Re: EMAC TX buffer runs full when no connection is established "emac_esp32_transmit(): insufficient TX buffer size"
Hi @DSchmid, this is known issue, please see https://github.com/espressif/esp-idf/issues/10851. It already has been fixed at master branch. Now, it is waiting to be backported to v5.0.
- Mon Apr 03, 2023 4:25 pm
- Forum: ESP32 Arduino
- Topic: IP settings for WT32 ETH01?
- Replies: 2
- Views: 3868
Re: IP settings for WT32 ETH01?
Based on your description, it seems you configured the same IP address on your PC and in the ESP32 code. I set the IP to 192.168.0.112 and the gateway to 192.168.0.1 in the code in the code, then on my laptop(running windows 10) I set the ethernet ipv4 properties to match this: IP Address: 192.168.0...
- Mon Feb 27, 2023 7:22 am
- Forum: General Discussion
- Topic: JL1101 Support
- Replies: 3
- Views: 3054
Re: JL1101 Support
There is no such a driver in the ESP-IDF. However, you could try to write your own. It should not be that hard since it seems the JL1101 has standard IEEE 802.3 RMII/MII interface. You can follow the guideline at https://blog.espressif.com/esp-idf-custom-ethernet-phy-driver-quick-guide-45f9d23de0ad ...
- Wed Feb 08, 2023 12:19 pm
- Forum: ESP-IDF
- Topic: eth2ap gets ethernet link down and up repeatedly
- Replies: 12
- Views: 73239
Re: eth2ap gets ethernet link down and up repeatedly
GPIO17 should not be that much affected. However, a PCB design may affect that and PHY chip's robustness is also another side. Different behavior might be observed with different PHY chips. There might be incorrect phase shift in CLK or other issues with signal integrity... You can try to use GPIO16...
- Mon Feb 06, 2023 9:06 am
- Forum: ESP-IDF
- Topic: eth2ap gets ethernet link down and up repeatedly
- Replies: 12
- Views: 73239
Re: eth2ap gets ethernet link down and up repeatedly
Using APPL CLK directly on the GPIO0 as a source for RMII REF CLK is experimental feature. There was really an issue observed when used along with WiFi under high traffic. This is documented in the Ethernet Configuration menu, please see below: GPIO0 can be set to output a pre-divided PLL clock (tes...
- Thu Jan 26, 2023 4:27 pm
- Forum: Hardware
- Topic: EMAC support: ESP32-WROOM-32 vs ESP32-S3-WROOM-1
- Replies: 3
- Views: 3727
Re: EMAC support: ESP32-WROOM-32 vs ESP32-S3-WROOM-1
ESP32 WROOM/WROVER support Ethernet. But ESP32-S and ESP32-C series does not support Ethernet. You can use Espressif Product Selector to help you to find appropriate product https://products.espressif.com/#/produc ... =en&names=
- Thu Jan 26, 2023 3:24 pm
- Forum: Hardware
- Topic: EMAC support: ESP32-WROOM-32 vs ESP32-S3-WROOM-1
- Replies: 3
- Views: 3727
Re: EMAC support: ESP32-WROOM-32 vs ESP32-S3-WROOM-1
Hi taoglas,
ESP32-S3 is different chip! Please see ESP32 modules datasheets at https://www.espressif.com/en/products/modules/esp32
Edit: Just note that the Ethernet is currently (Q1.2023) supported only by ESP32 SoC.
Regards
Ondrej
ESP32-S3 is different chip! Please see ESP32 modules datasheets at https://www.espressif.com/en/products/modules/esp32
Edit: Just note that the Ethernet is currently (Q1.2023) supported only by ESP32 SoC.
Regards
Ondrej
- Wed Jan 18, 2023 8:37 am
- Forum: ESP-IDF
- Topic: SPI master MOSI starts later than SCK when network activity
- Replies: 8
- Views: 3901
Re: SPI master MOSI starts later than SCK when network activity
SPI and EMAC shares the DMA. Could you please try to decrease `dma_burst_len` in your EMAC config (`eth_esp32_emac_config_t esp32_emac_config`) to e.g. `ETH_DMA_BURST_LEN_2`?
- Tue Jan 17, 2023 8:39 am
- Forum: General Discussion
- Topic: Esp-idf 4.4 and Ethernet phy device ksz8091
- Replies: 1
- Views: 1185
Re: Esp-idf 4.4 and Ethernet phy device ksz8091
Yes, you can use it. The ESP-IDF PHY driver "runs" the PHY chip only in the basic mode and this is the same for both chips.
Difference between the chips is described here:
https://microchipsupport.force.com/s/ar ... ernet-PHYs
Difference between the chips is described here:
https://microchipsupport.force.com/s/ar ... ernet-PHYs